Years
About 3,021 results
http://www.neo7cnc.com Cutting out a circle hang tag for my father. 3mm plastic sheet. 2 flute .25 inch carbide endmill at 25k RPM ...
From: Neo7CNC
Added: 15 years ago
Views: 26,002
http://www.neo7cnc.com *** SOLD *** I'm focusing on my larger CNC and don't have time for the mini. I need the shop space as ...
From: Neo7CNC
Added: 16 years ago
Views: 14,570
http://www.neo7cnc.com Modified a few parts to make the Z axis higher and tighter. Going to test a Bosch 1617 router as the ...
From: Neo7CNC
Added: 16 years ago
Views: 10,334
http://www.neo7cnc.com I'm cutting some pine for a project for my wife. .75 pine with a .25 2 fl carbide cutter. Cutting @ 70 ipm ...
From: Neo7CNC
Added: 16 years ago
Views: 5,535
http://www.neo7cnc.com Jog the CNC after reassembly. Need new method for mounting LED lights and air blower because of ...
From: Neo7CNC
Added: 16 years ago
Views: 7,352
http://www.neo7cnc.com I'm cutting some pine for a project for my wife. .75 pine with a .25 2 fl carbide cutter. Cutting @ 50 ipm ...
From: Neo7CNC
Added: 16 years ago
Views: 2,938
http://www.neo7cnc.com Finished installing the profile sections on the uprights. Cut, tapped and installed the cross member ...
From: Neo7CNC
Added: 16 years ago
Views: 8,087
http://www.neo7cnc.com Assembled all the newly modified Z and Y axis parts. Talk about stepper to actuator mounting plate.
From: Neo7CNC
Added: 16 years ago
Views: 7,243
http://www.neo7cnc.com Putting it back together after countersinking the bolts on the uprights. I was able to mill the bearing ...
From: Neo7CNC
Added: 16 years ago
Views: 14,727
http://www.neo7cnc.com Wired up the 2 new solid state relays. Installed some corner brackets to try and make the Y axis a little ...
From: Neo7CNC
Added: 16 years ago
Views: 7,970
http://www.neo7cnc.com I grounded the machine to try and stop some rare but odd issues. The rear shield to stop chips works well ...
From: Neo7CNC
Added: 16 years ago
Views: 14,111
http://www.neo7cnc.com *** SOLD *** Here is the controller.
From: Neo7CNC
Added: 16 years ago
Views: 30,681
http://www.neo7cnc.com First cut with stiffer machine. Ran the old spacer job at @58IPM. Left very clean cut and no chatter!
From: Neo7CNC
Added: 16 years ago
Views: 21,972
http://www.neo7cnc.com Explanation of Start and Pause buttons as connected to Mach3.
From: Neo7CNC
Added: 16 years ago
Views: 11,348
http://www.neo7cnc.com Getting ready to make the uprights stiffer. Had to take the y axis apart.
From: Neo7CNC
Added: 16 years ago
Views: 11,980
http://www.neo7cnc.com Installed brackets on motor mount for the air blower and lights. Got the aluminum bearing profile from ...
From: Neo7CNC
Added: 16 years ago
Views: 8,201
http://www.neo7cnc.com Added rear curtain to help contain chips. Re-attached the flap that protects the Z axis ballscrew from ...
From: Neo7CNC
Added: 16 years ago
Views: 18,278
http://www.neo7cnc.com This is my newly re-built homemade CNC router cutting a 3 inch by 3 inch by .125 inch DOC Tiger Paw in ...
From: Neo7CNC
Added: 16 years ago
Views: 15,409
http://www.neo7cnc.com Wired up the Y axis and added resistor. I have it working as a home switch but still need to set it up in ...
From: Neo7CNC
Added: 16 years ago
Views: 22,969
Help support Neo7CNC on PayPal or Patreon - Thanks! https://www.paypal.me/neo7cnc https://www.patreon.com/neo7cnc ...
From: Neo7CNC
Added: 16 years ago
Views: 136,644
