Years
About 28 results
Come Visit the website: http://www.h2o2fromh2o.oregonsouth.com Update: Original Release Part 1 of 2 The Current HE is a 0 to ...
From: H2O2FromH20
Added: 17 years ago
Views: 3,863
In this episode hole positions for Positive, Negative, Cell and MosFet mounts. This is My Concept of what a PWM case should look ...
From: H2O2FromH20
Added: 17 years ago
Views: 2,176
Information On Building This at http://www.h2o2fromh2o.oregonsouth.com Update: 1/212/2009: The Plans are ready come and ...
From: H2O2FromH20
Added: 17 years ago
Views: 2,662
Come Visit the website: http://www.h2o2fromh2o.oregonsouth.com Update: 8-17-2009 I have reduced the heating problem by ...
From: H2O2FromH20
Added: 17 years ago
Views: 1,206
http://www.h2o2fromh2o.us.tc Please come to my website and follow the link DIY-Projects Update 3/3/2010: Beta Testing is ...
From: H2O2FromH20
Added: 17 years ago
Views: 3,045
In this episode, Finish Board Calibration, Optional Confidence Test. This is My Concept of what a PWM case should look like.
From: H2O2FromH20
Added: 16 years ago
Views: 808
In this episode, PWM installation, Peek Current, Final Current Limiting setting, Is my PWM Capable of 100%, What is the MosFet ...
From: H2O2FromH20
Added: 16 years ago
Views: 1,556
In this episode MosFet Electro Static Discharge (ESD) Handling, Bending MosFet Pins, Building the Heat Sink System. Applying ...
From: H2O2FromH20
Added: 17 years ago
Views: 701
In this episode, Board Verification & Rough Calibration. This is My Concept of what a PWM case should look like. Minimal cooling ...
From: H2O2FromH20
Added: 16 years ago
Views: 801
In this episode, finish mounting PCB with hardware and checking PCB for fit, soldering wires to PCB, soldering techniques for ...
From: H2O2FromH20
Added: 16 years ago
Views: 966
In this episode Heat Sinks: Finishing up preparation to mount them. This is My Concept of what a PWM case should look like.
From: H2O2FromH20
Added: 17 years ago
Views: 412
In this episode Pre-fit Terminals, Securing terminals to #10 Screws, Positions of C5 and C7, then tightening terminals. This is My ...
From: H2O2FromH20
Added: 17 years ago
Views: 567
In this episode Soldering Techniques for soldering Large Lugs, Soldering Positive terminal, Soldering Cell Negative terminal, ...
From: H2O2FromH20
Added: 17 years ago
Views: 891
In this episode Heat Sinks; Drilling Tapping and Mounting. This is My Concept of what a PWM case should look like. Minimal ...
From: H2O2FromH20
Added: 17 years ago
Views: 470
In this episode C7 and C5 Placement Explained, Positioning R12, C5 Bending legs, Soldering C5 and C7 Positive legs, Preparing ...
From: H2O2FromH20
Added: 17 years ago
Views: 592
In this episode Soldering MosFet Drains to Cell negative wire , Good soldering techniques, soldering Sense Wires on to R12 to ...
From: H2O2FromH20
Added: 17 years ago
Views: 878
In this episode, Counter Sink PCB mount holes in case, Install Hex Screw/ Jack Screw, Drilling PCB & Installing it. This is My ...
From: H2O2FromH20
Added: 16 years ago
Views: 444
In this episode, Tighten Cell Negative Lug Screw to out Side Nut, Mark, Punch and Drill PCB mounting holes.This is My Concept ...
From: H2O2FromH20
Added: 16 years ago
Views: 555
In this episode wire cutting and positioning, Pre-tining wires, Soldering Gates, Cell negative Service loop and wire positioning, ...
From: H2O2FromH20
Added: 17 years ago
Views: 1,367
Come Visit the website: http://www.h2o2fromh2o.oregonsouth.com Update: Original Release The Test is repeated but this time At ...
From: H2O2FromH20
Added: 17 years ago
Views: 2,522
